Hyundai Santa Cruz: Smart Cruise Control (SCC) / Smart Cruise Control Settings
Setting features
Turning on Smart Cruise Control
![](images/smart_cruise_control_settings-1630/1344/pages.7(5).jpg)
- Press the Driving Assist (
)
button
to turn on Smart Cruise Control. The
speed will be set to the current speed
on the cluster.
- If there is no vehicle in front of you,
the set speed will be maintained, but
if there is a vehicle in front of you,
the speed may decrease to maintain
the distance to the vehicle ahead. If
the vehicle ahead accelerates, your
vehicle will travel at a steady cruising
speed after accelerating to the set
speed.
Information
- If your vehicle speed is between 0-20
mph (0-30 km/h) when you press the
Driving Assist button, the Smart Cruise
Control speed will be set to 20 mph (30
km/h).
- The Driving Assist button symbol may
vary depending on your vehicle option.
Setting vehicle distance
![](images/smart_cruise_control_settings-1630/1344/pages.8(5).jpg)
Each time the button is pressed, the
vehicle distance changes as follows:
![](images/smart_cruise_control_settings-1630/1344/pages.9(5).gif)
Information
- If you drive at 56 mph (90 km/h), the
distance is maintained as follows:
Distance 4 -
approximately 172 ft. (53 m)
Distance 3 -
approximately 130 ft. (40m)
Distance 2 -
approximately 106 ft. (30m)
Distance 1 -
approximately 82 ft. (25m)
- The distance is set to the last set
distance when the engine is restarted,
or when Smart Cruise Control was
temporarily canceled.
Increasing set speed
![](images/smart_cruise_control_settings-1630/1344/pages.10(5).jpg)
- Push the + switch up and release
it immediately. The set speed will
increase by 1 mph (1 km/h) each time
the switch is operated in this manner.
- Push the + switch up and hold it while
monitoring the set speed on the
cluster. The set speed will increase
by 5 mph or 10 km/h each time the
switch is operated in this manner.
Release the switch when the desired
speed is shown, and the vehicle will
accelerate to that speed. You can set
the speed to 110 mph (100 km/h).
WARNING
Check the driving condition before
using the + switch. Driving speed may
sharply increase when you push up and
hold the + switch.
Decreasing set speed
![](images/smart_cruise_control_settings-1630/1344/pages.11(5).jpg)
- Push the - switch down and release
it immediately. The set speed will
decrease by 1 mph (1 km/h) each time
the switch is operated in this manner.
- Push the - switch down and hold it
while monitoring the set speed on the
cluster. The set speed will decrease
by 5 mph or 10 km/h each time the
switch is operated in this manner.
Release the switch at the speed you
want to maintain. You can set the
speed to 20 mph (30 km/h).
Temporarily canceling Smart Cruise
Control
![](images/smart_cruise_control_settings-1630/1344/pages.12(5).jpg)
Press the
switch or depress the
brake pedal to temporarily cancel Smart
Cruise Control.
Resuming Smart Cruise Control
![](images/smart_cruise_control_settings-1630/1344/pages.13(6).jpg)
To resume Smart Cruise Control after the
function was canceled, push the +, - or
switch.
If you push the + switch up or - switch
down, vehicle speed will be set to the
current speed on the cluster.
If you push the
switch, vehicle
speed
will resume to the preset speed.
WARNING
Check the driving condition before
using the
switch. Driving
speed
may sharply increase or decrease when
you press the
switch.
![](images/smart_cruise_control_settings-1630/1344/pages.14(6).jpg)
Turning off Smart Cruise Control
Press the Driving Assist (
)
button to
turn Smart Cruise Control off.
Information
If your vehicle is equipped with Manual
Speed Limit Assist, press and hold the
Driving Assist button to turn off Smart
Cruise Control. However, Manual Speed
Limit Assist will turn on.
Based on Drive Mode
Smart Cruise Control will change
acceleration based on the drive mode
selected from Drive Mode Integrated
Control system. Refer to the following
chart.
![](images/smart_cruise_control_settings-1630/1344/pages.15(5).jpg)
Information
- For more details on drive mode, refer
to “Drive Mode Integrated Control
System” section in chapter 6.
- Smart Cruise Control may not turn
on or off in some of the drive modes
for the operating conditions are not
satisfied.
- If your vehicle is not equipped with
Drive Mode Integrated Control system,
Smart Cruise Control accelerates your
vehicle at a normal level.
Warning Volume
![](images/smart_cruise_control_settings-1630/1344/pages.16(5).jpg)
With the engine on, select 'Driver Assistance>Warning Volume' from the
Settings menu to change the Warning
Volume to ‘High’, ‘Medium’ or ‘Low’ for
Smart Cruise Control.
If you change the Warning Volume,
the Warning Volume of other Driver
Assistance systems may change.
Information
If the engine is restarted, Warning Volume
will maintain the last setting.
Basic function
Smart Cruise Control is designed to
help detect the vehicle ahead and
help maintain the desired speed and
minimum distance between the vehicle
ahead.
Overtaking Acceleration Assist
...
Operating conditions
Smart Cruise Control operates when the
following conditions are satisfied.
Basic function
The gear is in D (Drive)
The driver’s door is closed
EPB (Electronic Parking Brake ...
Other information:
Hyundai Santa Cruz 2021-2024 Owners Manual: Washer Fluid
Checking the Washer Fluid Level
Check the fluid level in the washer fluid
reservoir and add fluid if necessary.
Plain water may be used during summer
months if washer fluid is not available.
However, use washer solvent with
antifreeze characteristics in cold climates
to prevent freezing.
WARN ...
Hyundai Santa Cruz 2021-2024 Owners Manual: Storage Compartment
WARNING
Never store cigarette lighters, propane
cylinders, or other flammable/explosive
materials in the vehicle. These items
may catch fire and/or explode if the
vehicle is exposed to hot temperatures
for extended periods.
WARNING
ALWAYS keep the storage compartment
covers closed securely whi ...